Advanced Intel. 8. Use 8. 02. 1. 1n channel width to set high throughput mode channel width in order to maximize performance. Auto (default): For band 5. MHz depending on the wireless access point or router. MHz. Note. The settings are available only if the adapter is an Intel. MIMO increases data throughput to improve the transfer rate. ![]() VIVOTEK’s IB8367A is an all-in-one bullet-style network camera designed for diverse outdoor applications. Equipped with a 2MP sensor enabling viewing resolution of. Windows Server 2003, Windows Server 2003 SP1 and SP2, and Windows Server 2003 R2 retired content. The content you requested has already retired. Cisco Wireless LAN Controller Configuration Guide, Release 7.0.116.0. Chapter Title. Chapter 7 - Configuring WLANs. PDF - Complete Book. The OmniVista 2500 Network Management System is a full range of applications and tools for network management, security and efficiency. Use the setting to enable or disable high throughput mode support (MIMO - 8. Enabled (Default)Disabled. Notes. The settings are available only if the adapter is an Intel. You can select . An administrator can enable or disable support for high throughput mode to reduce power consumption or conflicts with other bands or compatibility issues. Ad- hoc channel 8. Ad- hoc channel 8. You don't need to change the channel unless the other computers in the ad- hoc network are not using the default channel. ![]() ![]() ![]() If you must change the channel, select the allowed operating channel: 8. Default): Select when using 8. GHz) ad- hoc band frequency. Select when using 8. GHz) ad- hoc band frequency. De Wireless AC1750 Dual-Band Gigabit Cloud Router met AC Smartbeam technologie creëert een razendsnel thuisnetwerk dat al uw computer en mobiele apparaten met uw. ![]() ![]() Note. The settings are available only if the adapter is an Intel. WMM* (Wi- Fi Multimedia*) is the Qo. S certification of te Wi- Fi Alliance* (WFA). ![]() When WMM is enabled, the adapter uses WMM to support priority tagging and queuing capabilities for Wi- Fi networks. WMM Enabled WMM Disabled (Default)Note. When your computer has an Intel. If disabled, Bluetooth HS is turned off. Fat channel intolerant. The setting communicates to surrounding networks that the Wi- Fi adapter is not tolerant of 4. MHz channels in the 2. GHz band. The setting's default is disabled (turned off) so that the adapter does not send this notification. Note. The settings are available only if the adapter is an Intel. Use Request to Send/Clear to Send (RTS/CTS) in an environment where clients may not hear each other. Use CTS- to- self to gain more throughput in an environment where clients are within hearing proximity. Note. The setting is not valid when 8. Preferred band. No Preference. Prefer 2. 4 GHz band. Prefer 5. 2 GHz band. Roaming aggressiveness. Define how aggressively your Wi- Fi client roams to improve connection to an access point. Click Use default value to balance between not roaming and performance. Lowest: Your wireless client won't roam. Only significant link quality degradation causes it to roam to another access point. Medium- Low/Medium- High: Allow roaming. Medium: Balanced setting between not roaming and performance. Highest: Your Wi- Fi client continuously tracks the link quality. If any degradation occurs, it tries to find and roam to a better access point. Throughput Enhancement/Booster. Enhance the transmit throughput by enabling packet bursting. The default setting is Disable. Transmit power. The optimal setting is to set the transmit power at the lowest possible level still compatible with communication quality. The setting allows the maximum number of wireless devices to operate in dense areas. It reduces interference with other devices that share the radio spectrum. If you decrease the transmit power, you reduce the radio coverage. Lowest: Sets the adapter to the lowest transmit power. Increase the number of coverage areas or confine a coverage area. You should reduce the coverage area in high traffic areas to improve overall transmission quality and avoid congestion or interference with other devices. Medium- low/Medium/Medium- high: Set by country requirements. Highest (Default): Sets the adapter to a maximum transmit power level. Use this setting for maximum performance and range in environments with limited radio devices. Note. This setting takes effect when either Network (Infrastructure) or Device to Device (ad- hoc) mode is used. Wake on magic packet. If enabled, the setting wakes the computer from a sleep state when it receives a . The magic packet contains the MAC address of the intended destination computer. Enabling turns on Wake on Magic Packet. Disabling turns off Wake on Magic Packet. It only disables the magic packet feature, not Wake on Wireless LANWake on pattern match. The feature wakes the computer from a sleep state when an adapter receives a particular wake pattern. Window 7* and Windows 8* support the feature. Patterns are typically: Wake on new incoming TCP connection for IPv. IPv. 6 (TCP SYN IPv. TCP SYN IPv. 6)Wake on 8. Disabling only disables the pattern match feature, not Wake on Wireless LAN. Wireless mode. The setting allows you to select whether the adapter operates in the 8. Connect the wireless adapter to 8. Connect the wireless adapter to 8. Connect the wireless adapter to 8. Connect the wireless adapter to 8. Default): Connect to 8. Note. To enable 8. Wireless mode and select HT mode for 8. VHT mode for 8. 02. HT mode. NS offloading for WOWLANNS offload is the ability of the network adapter to respond to a Neighbor Discovery Neighbor Solicitation request with a Neighbor Advertisement without waking the computer. Both the hardware and the driver must support NS offload to enable this feature. Packet Coalescing. The feature enables power saving by reducing the number of receive interrupts. The feature reduces receive interrupts by coalescing random broadcast or multicast packets. ARP offloading for WOWLANARP offload is the network adapter's ability to respond to an IPv. ARP request without waking the computer. To enable the feature, both the hardware and the driver must support ARP offload. GTK rekeying for WOWLANGroup Temporal Key (GTK) Rekey is used to encrypt and decrypt network traffic. HT mode. The setting lets you select HT Mode (High Throughput mode), select VHT Mode (Very High Throughput Mode), or disable both modes. Disabled. HT mode (supports 8. VHT mode (supports 8. Sleep on WOWLAN disconnect. Sleep on WOWLAN Disconnect is the ability to put the device to sleep/drop connection when WOWLAN is disconnected. U- APSD supportu. APSD (or WMM- Power Save or WMM- PS) is a Wi. Fi capability that saves power consumption on low periodic latency- sensitive traffic modes, like a VOIP. We have identified IOT (interoperability) issues with certain access points that result in reduced Rx throughput.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
October 2017
Categories |